Automatic Large Square Cable Peeling Stripping Machine (WG-9950)

WG-9950 Functional characteristics:
WG-9950 Automatic large square cable stripping machine is designed for the large square cable processing research and development equipment, it automatically complete the delivery line, tangent, rotating peeling, peeling. This device solves the difficult problem of processing large square cable in the market, and also changes the traditional parting (end) processing method.
WG-9950 Features: The machine adopts two large belt feeding units, a set of cut-off units, two sets of independent clamping units, two sets of rotary cutting units and two collection of scrap units. From the line into the cut, to the rotary cutting, then to the peeling, the whole computer control. Two sets of independent feeding mechanism using 4 high-power servo motor control respectively feed and discharge, changed the traditional way by the belt clamping cable back and forth of the peeling, such as encountering large adsorption force of the line skin, belt clamping cable in the process of pulling the skin may slip, directly affect the length of the cable precision. When the cable to cut off the edge (can be more than a bit, can also just to the edge of the knife), start the machine, cut off the knife to do the operation, the latter two feed seat to do the opposite direction of movement to the edge, the cable to the rotary cutting edge, clamping line Unit clamping Cable Two rotary knife at the same time rotating cutting both ends, cutting to the set value, micro-retract, after the use of rotary knife wire peel out of the rotary cutter 4 pieces per head, regardless of opening and closing, the middle Cheng Fangkong state, so that in the pull is the cable will not run off Using the screw to move the entire rotating cutting unit to remove the wire skin, so that the length of the cable and the total length of the wire will not be affected, from the increase in the accuracy of the cable length, this process is not like traditional stripping opportunity to waste the front of a cable. After the two clamping lines are clamped, the scrap is sent out along the scrap conveying unit. This way both ends are peeled at the same time, which improves production efficiency Changed the traditional first stripping end, the rear stripping end of the processing method, but also do not waste wire In the rotary cutting unit, the control of the rotary cutter is the use of servo motor with ball screw, rotary peeling is also the use of ball screw peeling, thereby improving the processing accuracy of the large square cable.

 











  WG-9950 Functional characteristics:
WG-9950 Automatic large square cable stripping machine is designed for the large square cable processing research and development equipment, it automatically complete the delivery line, tangent, rotating peeling, peeling. This device solves the difficult problem of processing large square cable in the market, and also changes the traditional parting (end) processing method.
WG-9950 Features: The machine adopts two large belt feeding units, a set of cut-off units, two sets of independent clamping units, two sets of rotary cutting units and two collection of scrap units. From the line into the cut, to the rotary cutting, then to the peeling, the whole computer control. Two sets of independent feeding mechanism using 4 high-power servo motor control respectively feed and discharge, changed the traditional way by the belt clamping cable back and forth of the peeling, such as encountering large adsorption force of the line skin, belt clamping cable in the process of pulling the skin may slip, directly affect the length of the cable precision. When the cable to cut off the edge (can be more than a bit, can also just to the edge of the knife), start the machine, cut off the knife to do the operation, the latter two feed seat to do the opposite direction of movement to the edge, the cable to the rotary cutting edge, clamping line Unit clamping Cable Two rotary knife at the same time rotating cutting both ends, cutting to the set value, micro-retract, after the use of rotary knife wire peel out of the rotary cutter 4 pieces per head, regardless of opening and closing, the middle Cheng Fangkong state, so that in the pull is the cable will not run off Using the screw to move the entire rotating cutting unit to remove the wire skin, so that the length of the cable and the total length of the wire will not be affected, from the increase in the accuracy of the cable length, this process is not like traditional stripping opportunity to waste the front of a cable. After the two clamping lines are clamped, the scrap is sent out along the scrap conveying unit. This way both ends are peeled at the same time, which improves production efficiency Changed the traditional first stripping end, the rear stripping end of the processing method, but also do not waste wire In the rotary cutting unit, the control of the rotary cutter is the use of servo motor with ball screw, rotary peeling is also the use of ball screw peeling, thereby improving the processing accuracy of the large square cable.

 











 

DU Bushing

Oiles Bronze Bearing, Plain Bearing ,Bearing Accessories,Other Bearing

Oiles Bronze Bearing,Wrapped Bronze Bushing Co., Ltd. , http://www.nbbushing.com