Second-hand car broke down ten emergency response trick
When buying a used car, the most worrying issue is the problem of the anchoring of the vehicle in the middle of the journey. Foreign trade has searched for some tricks about 10 emergency when the second-hand car broke down. You may wish to write it down. Maybe you will use it one day.
First, the inlet and outlet hose rupture is not large, you can use a layer of soap coated cloth to seal the leak; if the crack is large, the hose can be cut off at the middle of a bamboo tube or iron tube , and tied with wire.
Second, the fan belt can break the broken belt with a wire tie or open and stop the car to drive away.
Third, the screw hole slide fastener can cause oil leaks or loose links, making it unable to work. At this time, the original screw can be flattened with a hammer, so that the expansion of both sides of the expansion and then tightened, but not dismantled many times, to be repaired when the next maintenance.
Fourth, the fuel tank damage When the vehicle is in use, it is found that the oil leakage from the fuel tank can be wiped clean at the oil spill, coated with soap or bubble gum at the oil spill, and temporarily blocked; repaired with epoxy resin adhesive, the effect is better.
Fifth, the rupture of the tubing When the tubing ruptures, the broken part can be wiped clean, coated with soap, wrapped with a piece of cloth or tape around the broken part of the tubing, and tied with iron wire, and then coated with a layer of soap.
Sixth, tubing fractured tubing can be found when the root and tubing diameter to adapt to the rubber or plastic tube socket. If the socket is not tight enough, the two ends are tied with wire to prevent oil leakage.
Seventh, the cylinder head appears trachoma and oil leakage, water leakage can be based on the size of the trachoma, use the electric fuse with the corresponding specifications, and gently poke it into the trachoma with a hand hammer to eliminate oil leakage and water leakage.
Eight, when the oil pipe joint is used in the oil spill vehicle, if the engine oil pipe joint leaks, the tubing bell mouth and the oil pipe nut are mostly not sealed. The cotton yarn can be wrapped around the lower edge of the horn, and the tubing nut and tubing connector can be tightened. The bubble gum or maltose can also be chewed into a paste and coated on the tubing nut seat. After sealing, it can be sealed.
Nine, the diaphragm or the diaphragm of the oil pump ruptures or breaks. The diaphragm can be taken out by the oil pump, and then sawn with a plastic board, an electrical insulating bakelite or a plastic cloth according to the original shape and size, and polished.
10. After the valve spring is broken and the valve spring is broken, the broken spring can be removed and the broken two sections can be installed in reverse. You can also find a piece of 1 mm thick sheet metal, cut into 1 mm larger than the spring diameter of the disk, cut a round hole inside, the diameter is less than the spring diameter of 4 mm, the outer edge of every 6 mm into a 4 mm long slit, cut After every good one piece is folded one by one to form a double-sided spring seat groove, and then the spring turn head can be used in the tin groove.
First, the inlet and outlet hose rupture is not large, you can use a layer of soap coated cloth to seal the leak; if the crack is large, the hose can be cut off at the middle of a bamboo tube or iron tube , and tied with wire.
Second, the fan belt can break the broken belt with a wire tie or open and stop the car to drive away.
Third, the screw hole slide fastener can cause oil leaks or loose links, making it unable to work. At this time, the original screw can be flattened with a hammer, so that the expansion of both sides of the expansion and then tightened, but not dismantled many times, to be repaired when the next maintenance.
Fourth, the fuel tank damage When the vehicle is in use, it is found that the oil leakage from the fuel tank can be wiped clean at the oil spill, coated with soap or bubble gum at the oil spill, and temporarily blocked; repaired with epoxy resin adhesive, the effect is better.
Fifth, the rupture of the tubing When the tubing ruptures, the broken part can be wiped clean, coated with soap, wrapped with a piece of cloth or tape around the broken part of the tubing, and tied with iron wire, and then coated with a layer of soap.
Sixth, tubing fractured tubing can be found when the root and tubing diameter to adapt to the rubber or plastic tube socket. If the socket is not tight enough, the two ends are tied with wire to prevent oil leakage.
Seventh, the cylinder head appears trachoma and oil leakage, water leakage can be based on the size of the trachoma, use the electric fuse with the corresponding specifications, and gently poke it into the trachoma with a hand hammer to eliminate oil leakage and water leakage.
Eight, when the oil pipe joint is used in the oil spill vehicle, if the engine oil pipe joint leaks, the tubing bell mouth and the oil pipe nut are mostly not sealed. The cotton yarn can be wrapped around the lower edge of the horn, and the tubing nut and tubing connector can be tightened. The bubble gum or maltose can also be chewed into a paste and coated on the tubing nut seat. After sealing, it can be sealed.
Nine, the diaphragm or the diaphragm of the oil pump ruptures or breaks. The diaphragm can be taken out by the oil pump, and then sawn with a plastic board, an electrical insulating bakelite or a plastic cloth according to the original shape and size, and polished.
10. After the valve spring is broken and the valve spring is broken, the broken spring can be removed and the broken two sections can be installed in reverse. You can also find a piece of 1 mm thick sheet metal, cut into 1 mm larger than the spring diameter of the disk, cut a round hole inside, the diameter is less than the spring diameter of 4 mm, the outer edge of every 6 mm into a 4 mm long slit, cut After every good one piece is folded one by one to form a double-sided spring seat groove, and then the spring turn head can be used in the tin groove.
Desk Gear Clock is desk clock. Put desk gear clock on the table, making your table bright and special and giving your life relax. Desk Gear Clock with moving gears makes you feel change and relax. Gears move independently of the Clock. Desk Gear Clock combines of art and time.
Our company is a professional manufacturer and exporter of a variety of handicrafts. Our company has been highly commented and trusted by the worldwide business partners for the diversity and high quality of our distinctive products in the past years.
Our business principle is "quality good, favorable price, timely delivery and top service".
Desk Gear Clock,Kids Desk Clock,Desk Clock,Gift Desk Clock
Guangzhou Huan Yu Clocking Technologies Co., Ltd. , https://www.mk-times.com