Rcyj Liquid Pipeline Permanent Iron Tramp Remover/Magnetic Separator for Surry

Introduction:
Liquid line magnetic ferrous traps designed to extract remove the ferrous materials from liquid and slurry lines in order to purify the material in the production process. Strong magnetic traps filter the flow and extract the unwanted ferrous metal. While the slurry and liquid flows around the magnetic tubes, a very strong magnetic field (generated by the neodymium NdFeB magnets inside of the tubes) traps all metallic particles on the surface of the tubes.
In the course of manual cleaning the inner part of the separator is taken out, the magnetic cores are pulled out of the tubes (by operating lever) and the captured magnetic impurities fall off the tubes spontaneously.
 
Application for high performance liquid ferrous metal trap magnets :
 As advanced liquid trap magnets,These easy cleaning in pipeline metal trap magnets are an ideal magnetic traps for removing super fine ferrous contamination from materials of liquid,Semi-liquid lines or air-conveying lines experienced in most cases with no appreciable pressure drop or reduction in flow rates. All units incorporate a sump type housing to trap ferrous particles. Liquid Traps may be installed horizontally, vertically, or on an angle without affecting their magnetic efficiency.



Technical Parameters

FAQ
Q: Are you a factory ? 
A:Yes,we are factory, which was established in 2006.
We focus on providing expert service including design, manufacture, installation & maintenance for the logistic industries & warehouse equipment.
Q: Terms of Payment:
A:30% of the total amount by TT as deposit, the balance to be paid by TT or L/C at sight before the machines leaving seller' factory.
100% irrevocable L/C at sight.
 Q:Time for preparation of goods:
A:The above machines shall be ready for delivery during 45 days from the date of receiving the deposit/LC, excluding the time of waiting for shipment. If there is any delay of delivery caused by seller, 3‰ of the total amount shall be paid to buyer each day, but this amount shall not exceed the amount of deposit; if the delay is caused by buyer, 3‰ of the total amount shall be paid to seller each day, but this amount shall not exceed 10% of total value of machines.       
 Q:Guarantee period:
   A:The guarantee period for the above machines is twelve months from the date of putting into use, but not exceeds twenty-four months after the machines leaving seller's factory. It is not applicable for quick wear parts.
Q: May I know the status of my order?
A: Yes. We will send you information and photos at different production stage of your order. Every step will be send to you in time.
Q: Can I customize shelving or racking at my own size?
  A: Sure.
Q: If i need the complete mineral processing line. is Baite able to help us build it?

A: Yes, we can help you combine a complete mineral processing line. and give you related professional advice as long as you need.
There is a rich experience engineer team of us. we had already build many mining projects in China & Overseas. You can believe our quality and service. 

Why Choose us?
1.Pre-sale services: enthusiasm
We provide you with the prophase plan, process flow design and manufacturer equipment according to your special demand.
2.one-year warranty to make sure your machine runs consistently.
We always offering lifelong services and provide spare parts for a long term,and repair main parts under right using for free in two years.
3.Technical services
3.1 Design of production line and solutions according to buyer's requirement.
3.2 In 7 days after the receipt of deposit, the seller shall provide related technical documents for equipment installation, in addition to those with special requirements.
3.3 Before delivery, the seller can modify the previous solutions according to buyer's requirement.   
4.After-sales service
4.1 During the installation and commissioning, the seller shall send technician to the site for instruction of installation and commissioning, and for training of workers.
4.2 If there is any equipment failure caused by the buyer, the seller shall assist the maintenance of machines and replacement of fittings, and charges appropriate fees.
4.3 Beyond the guarantee period, the seller can provide services and fittings at a most preferential price. 
4.4The seller can provide consultation and inspection services freely for other products, especially for the up-stream and down-stream products of our equipment. 

PACKAGE & Ship:

Work Shop View:

 

  Introduction:
Liquid line magnetic ferrous traps designed to extract remove the ferrous materials from liquid and slurry lines in order to purify the material in the production process. Strong magnetic traps filter the flow and extract the unwanted ferrous metal. While the slurry and liquid flows around the magnetic tubes, a very strong magnetic field (generated by the neodymium NdFeB magnets inside of the tubes) traps all metallic particles on the surface of the tubes.
In the course of manual cleaning the inner part of the separator is taken out, the magnetic cores are pulled out of the tubes (by operating lever) and the captured magnetic impurities fall off the tubes spontaneously.
 
Application for high performance liquid ferrous metal trap magnets :
 As advanced liquid trap magnets,These easy cleaning in pipeline metal trap magnets are an ideal magnetic traps for removing super fine ferrous contamination from materials of liquid,Semi-liquid lines or air-conveying lines experienced in most cases with no appreciable pressure drop or reduction in flow rates. All units incorporate a sump type housing to trap ferrous particles. Liquid Traps may be installed horizontally, vertically, or on an angle without affecting their magnetic efficiency.



Technical Parameters

FAQ
Q: Are you a factory ? 
A:Yes,we are factory, which was established in 2006.
We focus on providing expert service including design, manufacture, installation & maintenance for the logistic industries & warehouse equipment.
Q: Terms of Payment:
A:30% of the total amount by TT as deposit, the balance to be paid by TT or L/C at sight before the machines leaving seller' factory.
100% irrevocable L/C at sight.
 Q:Time for preparation of goods:
A:The above machines shall be ready for delivery during 45 days from the date of receiving the deposit/LC, excluding the time of waiting for shipment. If there is any delay of delivery caused by seller, 3‰ of the total amount shall be paid to buyer each day, but this amount shall not exceed the amount of deposit; if the delay is caused by buyer, 3‰ of the total amount shall be paid to seller each day, but this amount shall not exceed 10% of total value of machines.       
 Q:Guarantee period:
   A:The guarantee period for the above machines is twelve months from the date of putting into use, but not exceeds twenty-four months after the machines leaving seller's factory. It is not applicable for quick wear parts.
Q: May I know the status of my order?
A: Yes. We will send you information and photos at different production stage of your order. Every step will be send to you in time.
Q: Can I customize shelving or racking at my own size?
  A: Sure.
Q: If i need the complete mineral processing line. is Baite able to help us build it?

A: Yes, we can help you combine a complete mineral processing line. and give you related professional advice as long as you need.
There is a rich experience engineer team of us. we had already build many mining projects in China & Overseas. You can believe our quality and service. 

Why Choose us?
1.Pre-sale services: enthusiasm
We provide you with the prophase plan, process flow design and manufacturer equipment according to your special demand.
2.one-year warranty to make sure your machine runs consistently.
We always offering lifelong services and provide spare parts for a long term,and repair main parts under right using for free in two years.
3.Technical services
3.1 Design of production line and solutions according to buyer's requirement.
3.2 In 7 days after the receipt of deposit, the seller shall provide related technical documents for equipment installation, in addition to those with special requirements.
3.3 Before delivery, the seller can modify the previous solutions according to buyer's requirement.   
4.After-sales service
4.1 During the installation and commissioning, the seller shall send technician to the site for instruction of installation and commissioning, and for training of workers.
4.2 If there is any equipment failure caused by the buyer, the seller shall assist the maintenance of machines and replacement of fittings, and charges appropriate fees.
4.3 Beyond the guarantee period, the seller can provide services and fittings at a most preferential price. 
4.4The seller can provide consultation and inspection services freely for other products, especially for the up-stream and down-stream products of our equipment. 

PACKAGE & Ship:

Work Shop View:

 

 

Bearing is an important part of modern machinery and equipment. Its main function is to support the mechanical rotating body, reducing the friction coefficient of its movement, and to ensure the accuracy of its rotation.

We supply Tapered Roller Bearing , Deep Groove Ball Bearing and Thrust Ball Bearing.  They  mainly used for Mud Pump, Rotary Table,Crown Block and some other equipment in oil fields.

Bearing

Ball Bearing,Miniature Ball Bearings,Spherical Plain Bearing,Bimetal Slide Bearing

Baoji Baohao Petroleum Machinery Equipment Co., Ltd. , http://www.baohao-petro.com