Car Paint Baking Oven Bake Oven Paint Booth Spray Booth Paint Oven
BTD Car Tools Co., Ltd Â
is a professional manufacturer for car spraying, baking and largest automobile spraying/baking booth in South China since Year 2002 . With strong R&D experiences, advanced technology and guarantee quality , BTD brand spray booth is getting more and more popular all over the world .
Design Standard |
BS EN 13355:2004+A1:2009 BS EN 60204:2006+A1:2009 |
Cabin size | Â |
inside size | 7000x4000x2800(LxWxH) |
outside size | 7110x5800x3810(LxWxH) |
Basement | Â |
Foundation | Adopt galvanized bending forming, more durable and strong. Full grid, Basement height is 350mm. |
Capability of load | Hold up 700kg/wheel. |
Filter surface area | 27 M²(full galvanized grids) |
Drive in ramp | 3 big drive-in ramps + 2 side ramps, has multi-angle drive-in function, each size: 2000x1030mm, diamond plate structure. |
Description of floor grids | Size: 997*756mm , 40*3mm,the grids are suppressive type of steel grating instead of traditional twisted steel for the cross bar steel grating. The biggest features for it are beautiful, durable and better force bearing. |
Cabin system | Â |
Cabin structure | Wall vertical plugging |
Pressure room height | 600mm |
Wall board | Â |
Wall panel | Thickness: 60mm, wallboard fill with rock wool |
Roof panel | Thickness: 50mm, wallboard fill with rock wool |
Edge material | 1.5mm galvanized steel plate bending forming |
Main door | Â |
Gate form | 3-folded entrance door with safety glass window, tempering glass observation window , size is bigger and view is better than traditional spray booth. |
Gate size | 3200X2700 mm (W×H) |
Quantity | 1sets |
Spray gun hanging system | Install hanging arm in cabin, convenient for operators to hang spray gun, etc. |
Service door | Â |
Service door form | With steel frame structure |
Service door size | 800×2000 mm  (W×H) |
Quantity | 1 set |
Description | With safety observation window, the top of service door installs door closer to close the door automatically |
Ceiling Light | Â |
Quantity and power | 8 sets of lighting box , each set with 4×58W, total 1856W |
Lighting arrangement | on both sides |
Description | IP55 protection grade, CE certification, electronic rectifier, Osram tubes |
Side Light | Â |
Quantity and power | 8 sets of lighting box , each set with 2×58W, total 928W |
Lighting arrangement | on both sides |
Description | IP55 protection grade, CE certification, electronic rectifier, Osram tubes |
Total Brightness | >1500Lux |
Filtration System | Â |
Pre-filters | Grade EU3 pocket type filter |
Ceiling filter | EU5 grade filter , filter model : SP-600G |
Floor filter | Fibreglass paint-stop filter |
Exhaust filter | Fibreglass paint-stop filter, with large air volume, low resistance and flame resistance ,etc. |
Ventilation system ( Air supply) |
 |
Inlet fan form | Direct turbo fan |
Inlet fan Power and motor description |
Germany SIEMENS Brand motor, 11KW,6-pole motor,  970RMP, 380V,50HZ |
Fan air volume | 32000m³/h |
Ventilation system ( Air exhaust) |
 |
Outlet fan form | Direct turbo fan |
Outlet fan Power and motor description |
Germany SIEMENS Brand motor, 11KW,6-pole motor,  970RMP, 380V,50HZ |
Fan air volume | 32000m³/h |
Total air volume | 32000m3/h |
Painting and baking exchange system | Solenoid valve+ pressure adjustment control cylinder driven damper exchange |
Empty load air flow speed | 0.30m/s , inverter control |
Noise | <78 Decibel |
Heating system | Â |
Material of heat exchanger | Adopt high efficient heat-resistant stainless steel as cycling heat exchanger |
Power of heat exchanger | 320KW(340.000Kcal/H)Â |
△T Temperature capability | 20°C(from -10°C to 20°C painting state) |
Max operating temperature | 80°C |
Heating time | 2-4 mins (from 20° to  60°ºС) baking state |
Burner Model | Adopt Italy RIELLO two range diesel burner RL34-2(340.000kcal/H),quicker heating and much better effect, more rest assure for quality |
Energy-saving system | Model E-32000, When warm painting, the energy-saving system can collect exhaust air's energy to heat the cold fresh air, then through second heating by furnace, the temperature of air in cabin will be increased quicker, more energy-saving, more environmental |
Control system | Â |
Executive standard | Inverter control system(more energy-saving, more economic) |
PLC controller | Yes, PLC control, more reliable, lower breakdown rate |
Human-computer interface touching screen control system | Yes, touching screen control, easier to operate |
Ceiling and floor filter change reminder function | Ceiling filter and floor filter install differentiate pressure transmitter, when the ceiling and floor filter suck dust and paints to certain level, the control system will remind user to change filter humanely. |
Function | Painting, warm painting, baking, leveling, emergency stop switch, inverter, pressure adjust balance, failure indication, over-temperature alarm indication, baking delay stop protection |
Special Note Project | Â |
FAQ
Q1: What's the sort of heating types?
BTD reply: There are diesel, gas and electricity(infrared lamp) heating.
Q2: Does the BTDÂ spray booth with the European design ?
BTD reply: Our products are welcomed in Europe. All the spray booths are according to European standard with CE certificate.Â
Q3: What are range of the voltage and power for BTDÂ spray booth when operating?
BTD reply: the standard voltage and power for our products is 220V 50HZ 1PH for lights (Residential voltage), 380V 50HZ 3PH for motors (Industrial voltage), we could modify the voltage to suitable for customer's local voltage.Â
Q4: For the customer-design spray booth for other workpieces, does BTDÂ could provide?
BTD reply: Absolutely yes, BTDÂ has the professional team with 12 years of design experience. BTDÂ may design according to customers requirements of spray booth for car, bus, big iron workpieces, wooden furniture etc.
Contact us:
BTD Car Tools Co., Ltd  | |
Mobile: |
 +86 15089398679 |
 TEL: |
+86-663-6187007Â |
 |
 |
 |
 |
ADD: |
Mazha Industrial Park,Liusha ,Puning ,Guangdong |
PC: |
515300 |
Â
Metal forging is a processing method that uses a forging machine to apply pressure to a metal blank to make it a part of a certain shape and size. The forging process can change the metal structure and improve the metal properties, making it have higher mechanical properties than the raw materials. Therefore, forging is usually given priority to workpieces that require relatively high strength and heavy load-bearing. Because the forging process is a process of up and down pressing, the structure of the workpiece cannot be too complicated, and only some workpieces with a relatively simple structure can be formed. If the structure of some workpieces is relatively complex, we can form a structure that can be forged, and then obtain the desired structure through subsequent secondary CNC machining, but the relative cost will be relatively high.
SCZY has very rich experience in metal forging, as well as subsequent secondary CNC machining and surface treatment. We are mainly engaged in the processing of forged parts such as aluminum alloy forging, copper alloy forging, carbon steel forging, alloy steel forging and Stainless Steel Forging, as well as subsequent secondary CNC machining and surface treatment. Here are a few photos of the products we've made:
Forging Parts,Forging Metal Parts,Forging Steel Parts,Forging Iron Parts
Shenzhen SCZY Technology Co.,Ltd , https://www.szsccasting.com