It is reported that some established car manufacturers, such as General Motors, although they claim to fully develop electric vehicles, still do not give up lobbying the government to relax fuel consumption standards. Relaxing fuel consumption standards means that the car's environmental impact will increase, and electric vehicles are considered to be environmentally friendly models, so some analysts pointed out that GM seems to have conflicts in environmental protection. However, from the perspective of promoting eco-cars, it is not contradictory, because it will highlight the cost-effectiveness of eco-cars such as electric vehicles.
There are reports that GM CEO Mary Barra is currently meeting with the Trump administration to discuss how to relax standards, and the US Environmental Protection Agency (EPA) even considers pressure on states to stop following California. Radical standards.
In the Obama era, US automakers reached an agreement that by 2025, the average fuel economy would be doubled to 54.5 miles per gallon.
The agreement encourages automakers to mass produce more energy-efficient vehicles such as electric vehicles to compensate for the adverse effects of SUVs and pickups that can generate significant profits for manufacturers.
Although major manufacturers initially agreed to the agreement, the industry has launched since Donald Trump was elected president and Scott Pruitt was appointed as the US Environmental Protection Agency. A new effort to change the rules. In fact, only two days after Trump was elected, the vendor lobby group sent a letter to the then Trump transition team to lobby the government to relax the rules. It is reported that the lobbying group covers almost all manufacturers except Tesla and several French car manufacturers.
After last year's continuous efforts, Pruitt finally made it clear that although the EPA's mission is to protect the environment, it is still possible to consider relaxing this provision.
According to Reuters, GM CEO Mary Bola recently met with the US Environmental Protection Agency and reconfirmed that the EPA will prioritize modern fuel consumption standards.
A spokesperson for GM said it needed a set of national standards that included the development of new technologies, such as increased sharing and self-driving electric vehicles.
The Alliance of Automobile Manufacturers made it clearer that even if major manufacturers comply with regulations, they are not sure whether consumers will buy a large number of electric vehicles.
Mitch Bainwol, the chief executive of the alliance, pointed out at the time that the combination of improved fuel efficiency and low oil prices in the early stages of the agreement would undermine consumer demand for higher-priced alternative powertrain vehicles (such as electric vehicles). The desire to buy, which also causes the automotive industry to comply with stricter fuel consumption standards in the next few years.
Banwo also believes that the current market demand for “alternative power systems†(ie electric vehicles) is not enough for automakers to meet fuel consumption requirements.
Although Bola continues to reaffirm that the future of the car will be all-electric, GM also plans to become the leader of electric vehicles, but the company has repeatedly expressed its support for the relaxation of standards. The contradictions that GM has shown here will continue in the later stages.
Automotive Plastic Parts
Automotive plastic parts are components made of various plastics that are used in the manufacture and repair of vehicles. These parts are used in various areas of the vehicle, including the interior, exterior, engine, and more. They are favored for their light weight, low cost and versatility.Automobile Parts.
1. Instrument Panel: This is the control panel located directly in front of the driver of the vehicle that displays the instruments and controls for vehicle operation.
2. Headlight and Taillight Covers: These covers are often made of polycarbonate due to its high impact resistance and ability to be formed into complex shapes.
3. Seat Belts: Although seat belts are not entirely made of plastic, seat belts often use plastic parts for their buckles and adjustment mechanisms.Car Spare Parts.
4. Air filters: They are usually made of various types of plastic and are used to filter out harmful particles from the air before it enters the engine.
5. Engine parts: Many parts of the engine, such as valve covers, oil pans, intake manifolds, etc., can be made of plastic to reduce weight and cost.
6. Radiator Fans: These fans are usually made of plastic due to their heat resistance and light weight.
7. Rim decorative cover, embedded on the wheel hub, plays a decorative role.Automobile Spare Parts
These are just a few examples of the many plastic components used in automotive applications. The use of plastics in vehicles continues to grow.Car Components.
Automobile Parts,Car Spare Parts,Automobile Spare Parts,Car Components
Kunshan Muchun Electric Co., LTD , https://www.muchunelectric.com
