How to accurately find electronic floor scale faults
A long series of problems may occur when electronic scales are used for a long time, which may result in inaccurate weighing of electronic scales or other problems. At this time, we need to check what problems have occurred in the electronic scales. It is easy to solve problems once they are found. The following small series will teach you how to accurately find the electronic scales fault, I hope you can read this article carefully, to bring you some help.
The first thing to do is to find out the location where the fault occurs. If the meter is turned on, the simplest method is to use the sensor simulator to check. When checking, connect the four-wire signal of the sensor simulator to the pin number of the corresponding interface of the instrument and turn on the power. If the instrument works normally, the fault is in the body of the scale. If the instrument is not working properly, the fault is in the instrument.
1, the instrument part of the failure: the exclusion of instrument failure must be carried out by professional inspectors, users can use the method of replacing the PCB board, first make the system back to normal, damaged PCB board sent to the repair department or manufacturer for repair.
2, the body part of the failure:
Check the junction box wiring board for moisture, corrosion, device aging, potentiometer loose, false welding, poor wiring contact. Exclusion methods are mainly used to dry hair dryer, replace the wiring board, add desiccant and so on.
Check the cable for a short circuit or disconnection. Use a multimeter to remove after measurement.
Check the level of deformation and the level of the countertop after loading on the countertop. 1.2.4 Check whether the limit dead or not. Adjust to a (2 to 3) mm gap.
3, sensor failure:
Use a digital multimeter to measure the resistance. The resistance between the sensor signal ±EX and ±SZ is 382±4Ω, and the resistance between the SI on the signal is 350±1Ω. If the measured data is not within this range, the sensor may need to be replaced.
Use a digital multimeter to measure the voltage. When the instrument is energized and the electronic scale is in the empty scale, the mV value between the ±200 mV measurement signal and the SI signal of the multimeter is between (2 and -3) mV. When the instrument is energized and the electronic scale is full scale, the mV value between the ± 200 mV measurement signal of the multimeter ± SI shall be less than 30 mV, otherwise the sensor may need to be replaced.
Use a digital multimeter to measure the insulation performance. Place the multimeter in the 20MΩ range. Connect one end of the meter to the shielded cable and connect the other end to ±EX, ±SE, ±SI, and the housing respectively. If “I†is displayed, the sensor insulation performance is good. . Otherwise, the sensor's dielectric strength is not up to the requirement, and the mV signal output by the sensor may be interfered by external electrical noise signals.
This article is shared by Shanghai Hengheng Electronic Technology Co., Ltd. If you want to learn more about electronic scales, please contact us! Thank you for your support!
Copper Pipe
Copper pipe is also known as copper pipe. A non-ferrous metal tube is a pressed and drawn seamless tube. Copper pipe has good electrical conductivity, thermal conductivity characteristics, electronic products of conductive parts and heat dissipation parts of the main material, and has become a modern contractor in all residential commercial housing water pipeline, heating, cooling pipe installation of the first choice. Copper pipe corrosion resistance is strong, not easy to oxidation, and some liquid substances are not easy to react chemically, easy to Wei bending shape.
Copper pipe (also known as red copper pipe), often used in water pipes, heating and cooling pipes, can be used in different environments. Copper pipe set the advantages of metal and non-metal pipe in a body, in the hot and cold water system exclusive torture, is the best connection pipe. Copper pipes are refractory and heat-resistant, and can maintain their shape and strength at high temperature without aging.
The pressure resistance of copper pipe is several times or even dozens of times that of plastic pipe and aluminum plastic pipe, and it can withstand the highest water pressure in today's buildings. In the hot water environment, with the extension of service life, the bearing capacity of plastic pipe significantly decreases, while the mechanical properties of copper pipe remain unchanged in all thermal temperature ranges, so its pressure resistance will not be reduced, nor will aging occur.
The linear expansion coefficient of copper pipe is very small, is 1/10 of plastic pipe, will not cause stress fatigue rupture because of excessive thermal expansion and cold contraction.
The strength of copper pipe is greater, and the outside diameter is smaller to ensure the effective inside diameter, which is more suitable for hidden burial.
Copper tube,Copper Pipe,Copper Coils Pipe
Shandong Longhao Steel Group Co., Ltd. , https://www.longhaosteels.com
